TSL1402R【PDF 11/17 页】IC LINEAR SENSOR ARRAY 256X1

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录57

7页 8页 9页 10页 [11页]12页 13页 14页 15页

TSL1402R

256 ?1 LINEAR SENSOR ARRAY WITH HOLD

TAOS041G NOVEMBER 2011

The LUMENOLOGY r Company

www.taosinc.com

APPLICATION INFORMATION

Integration Time

The integration time of the linear array is the period during which light is sampled and charge accumulates on

each pixels integrating capacitor. The flexibility to adjust the integration period is a powerful and useful feature

of the TAOS TSL14xx linear array family. By changing the integration time, a desired output voltage can be

obtained on the output pin while avoiding saturation for a wide range of light levels.

The integration time is the time between the SI (Start Integration) positive pulse and the HOLD positive pulse

minus the 18 setup clocks. The TSL14xx linear array is normally configured with the SI and HOLD pins tied

together. This configuration will be assumed unless otherwise noted. Sending a high pulse to SI (observing

timing rules for setup and hold to clock edge) starts a new cycle of pixel output and integration setup. However,

a minimum of (n+1) clocks, where n is the number of pixels, must occur before the next high pulse is applied

to SI. It is not necessary to send SI immediately on/after the (n+1) clocks. A wait time adding up to a maximum

total of 100 ms between SI pulses can be added to increase the integration time creating a higher output voltage

in low light applications.

Each pixel of the linear array consists of a light-sensitive photodiode. The photodiode converts light intensity

to a voltage. The voltage is sampled on the Sampling Capacitor by closing switch S2 (position 1) (see the

Functional Block Diagram on page 1). Logic controls the resetting of the Integrating Capacitor to zero by closing

switch S1 (position 2).

At SI input, all of the pixel voltages are simultaneously scanned and held by moving S2 to position 2 for all pixels.

During this event, S2 for pixel 1 is in position 3. This makes the voltage of pixel 1 available on the analog output.

On the next clock, S2 for pixel 1 is put into position 2 and S2 for pixel 2 is put into position 3 so that the voltage

of pixel 2 is available on the output.

Following the SI pulse and the next 17 clocks after the SI pulse is applied, the S1 switch for all pixels remains

in position 2 to reset (zero out) the integrating capacitor so that it is ready to begin the next integration cycle.

On the rising edge of the 19

clock, the S1 switch for all the pixels is put into position 1 and all of the pixels begin

a new integration cycle.

The first 18 pixel voltages are output during the time the integrating capacitor is being reset. On the 19

clock

following an SI pulse, pixels 1 through 18 have switch S2 in position 1 so that the sampling capacitor can begin

storing charge. For the period from the 19

clock through the n

clock, S2 is put into position 3 to read the output

voltage during the n

clock. On the next clock the previous pixel S2 switch is put into position 1 to start sampling

the integrating capacitor voltage. For example, S2 for pixel 19 moves to position 1 on the 20

clock. On the n+1

clock, the S2 switch for the last (n

) pixel is put into position 1 and the output goes to a high-impedance state.

If a SI was initiated on the n+1 clock, there would be no time for the sampling capacitor of pixel n to charge to

the voltage level of the integrating capacitor. The minimum time needed to guarantee the sampling capacitor

for pixel n will charge to the voltage level of the integrating capacitor is the charge transfer time of 20 約.

Therefore, after n+1 clocks, an extra 20 約 wait must occur before the next SI pulse to start a new integration

and output cycle.

The minimum integration time for any given array is determined by time required to clock out all the pixels

in the array and the time to discharge the pixels. The time required to discharge the pixels is a constant.

Therefore, the minimum integration period is simply a function of the clock frequency and the number of pixels

in the array. A slower clock speed increases the minimum integration time and reduces the maximum light level

for saturation on the output. The minimum integration time shown in this data sheet is based on the maximum

clock frequency of 8 MHz.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式